NOTICE:  BL2: R-Car H3/M3/M3N Initial Program Loader(CA57)
NOTICE:  BL2: Initial Program Loader(Rev.2.0.4)
NOTICE:  BL2: PRR is R-Car H3 Ver.2.0
NOTICE:  BL2: Board is Starter Kit Rev.1.0
NOTICE:  BL2: Boot device is HyperFlash(80MHz)
NOTICE:  BL2: LCM state is CM
[    0.022197] NOTICE:  BL2: AVS setting succeeded. DVFS_SetVID=0x53
NOTICE:  BL2: DDR3200(rev.0.37)
NOTICE:  BL2: [COLD_BOOT]
[    0.000351] NOTICE:  BL2: AVS setting succeeded. DVFS_SetVID=0x53
NOTICE:  BL2: CH0: 0x400000000 - 0x440000000, 1 GiB
NOTICE:  BL2: CH1: 0x500000000 - 0x540000000, 1 GiB
NOTICE:  BL2: CH2: 0x600000000 - 0x640000000, 1 GiB
NOTICE:  BL2: CH3: 0x700000000 - 0x740000000, 1 GiB
[    0.039614] NOTICE:  BL2: DRAM Split is 4ch
[    0.043758] NOTICE:  BL2: QoS is default setting(rev.0.21)
[    0.049201] NOTICE:  BL2: DRAM refresh interval 1.95 usec
[    0.054558] NOTICE:  BL2: Periodic Write DQ Training
NOTICE:  BL2: Lossy Decomp areas
NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
[    0.158250] ERROR:   Image magic is wrong!
[    0.160857] ERROR:   Bootloader partition 2 corrupted, setting unboot
[    0.167747] NOTICE:  BL2: v1.5(release):a3c4725
[    0.172089] NOTICE:  BL2: Built : 16:45:55, Mar 30 2020
[    0.177277] NOTICE:  BL2: Normal boot
[    0.180912] NOTICE:  BL2: eMMC boot from partition 1
[    0.185829] NOTICE:  BL2: Load dst=0xe632c100 src=(p:1)0x30000(384) len=0x200(1)
[    0.193347] NOTICE:  BL2: Load dst=0x43f00000 src=(p:1)0x30400(386) len=0x1800(12)
[    0.201007] NOTICE:  BL2: Load dst=0x44000000 src=(p:1)0x40000(512) len=0x10000(128)
[    0.209990] NOTICE:  BL2: Load dst=0x44100000 src=(p:1)0x80000(1024) len=0x100000(2048)
[    0.239202] NOTICE:  BL2: Load dst=0x50000000 src=(p:1)0x200000(4096) len=0x200000(4096)
[    0.291063] NOTICE:  BL2: Booting BL31


U-Boot 2018.09-g74e87ec (Mar 30 2020 - 16:45:46 +0300)

Config: r8a7795-h3ulcb-u-boot
CPU: Renesas Electronics R8A7795 rev 2.0
Model: Renesas H3ULCB board based on r8a7795 ES2.0+
DRAM:  3.9 GiB
Bank #0: 0x048000000 - 0x07fffffff, 896 MiB
Bank #1: 0x500000000 - 0x53fffffff, 1 GiB
Bank #2: 0x600000000 - 0x63fffffff, 1 GiB
Bank #3: 0x700000000 - 0x73fffffff, 1 GiB

MMC:   sd@ee100000: 0, sd@ee140000: 1
Loading Environment from MMC... OK
In:    serial@e6e88000
Out:   serial@e6e88000
Err:   serial@e6e88000
Net:   eth0: ethernet@e6800000
Setting bootmode 'android'
Hit any key to stop autoboot:  0
=> printenv
baudrate=115200
bootargs=video=LVDS-1:d video=VGA-1:d init_time=1585791913
bootcmd=boota 1 boot 0x4C000000 avb
bootdelay=3
bootmode=android
ethact=ravb
ethaddr=2e:09:0a:03:93:11
fdt_high=0xffffffffffffffff
fdtcontroladdr=7d6e2448
initrd_high=0xffffffffffffffff
loadaddr=0x58000000
platform=r8a7795
product=ulcb
recovery=setenv bootmode recovery; run bootcmd;
serialno=00025192
stderr=serial@e6e88000
stdin=serial@e6e88000
stdout=serial@e6e88000
ver=U-Boot 2018.09-g74e87ec (Mar 30 2020 - 16:45:46 +0300)

Environment size: 504/131068 bytes
=> setenv bootargs
=>setenv bootcmd
=>setenv fdt_high
=>setenv initrd_high
=>setenv ethaddr 2e:09:0a:03:93:11
=>setenv ipaddr 192.168.0.2
=>setenv serverip 192.168.0.1
=>setenv bootargs 'consoleblank=0 console=ttySC0,115200 rw root=/dev/nfs nfsroot=192.168.0.1:/nfs/h3ulcb ip=192.168.0.2'
=>tftp 0x48080000 /h3ulcb/Image
Using ethernet@e6800000 device
TFTP from server 192.168.0.1; our IP address is 192.168.0.2
Filename '/h3ulcb/Image'.
Load address: 0x48080000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ###################
         18.4 MiB/s
done
Bytes transferred = 16497152 (fbba00 hex)
=>tftp 0x48000000 /h3ulcb/Image-r8a7795-h3ulcb-kf.dtb
Using ethernet@e6800000 device
TFTP from server 192.168.0.1; our IP address is 192.168.0.2
Filename '/h3ulcb/Image-r8a7795-h3ulcb-kf.dtb'.
Load address: 0x48000000
Loading: #######
         17.5 MiB/s
done
Bytes transferred = 91875 (166e3 hex)
=>booti 0x48080000 - 0x48000000
## Flattened Device Tree blob at 48000000
   Booting using the fdt blob at 0x48000000
   Loading Device Tree to 0000000048066000, end 000000004807f6e2 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.75-ltsi-yocto-standard (oe-user@oe-host) (gcc version 7.3.0 (GCC)) #1 SMP PREEMPT Fri0
[    0.000000] Boot CPU: AArch64 Processor [411fd073]
[    0.000000] Machine model: Renesas H3ULCB Kingfisher board based on r8a7795 ES2.0+
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000057000000, size 400 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma@57000000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB
[    0.000000] OF: reserved mem: initialized node linux,multimedia@70000000, compatible id shared-dma-pool
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000073fffffff]
[    0.000000] NUMA: NODE_DATA [mem 0x73ff6cd00-0x73ff6e7ff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000048000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000073fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000048000000-0x0000000053ffffff]
[    0.000000]   node   0: [mem 0x0000000057000000-0x000000007fffffff]
[    0.000000]   node   0: [mem 0x0000000500000000-0x000000053fffffff]
[    0.000000]   node   0: [mem 0x0000000600000000-0x000000063fffffff]
[    0.000000]   node   0: [mem 0x0000000700000000-0x000000073fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000073fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS resident on physical CPU 0x0
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedded 24 pages/cpu @ffff8006ffea7000 s57624 r8192 d32488 u98304
[    0.000000] Detected PIPT I-cache on CPU0
[    0.000000] Speculative Store Bypass Disable mitigation not required
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 987840
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: androidboot.boottime=18.995 consoleblank=0 console=ttySC0,115200 rw root=/dev/nfs n2
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] software IO TLB [mem 0x4ffff000-0x53fff000] (64MB) mapped at [ffff80000ffff000-ffff800013ffefff]
[    0.000000] Memory: 3192800K/4014080K available (10364K kernel code, 686K rwdata, 4256K rodata, 768K init, 404K bss,)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffff000000000000 - 0xffff000008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000   (129022 GB)
[    0.000000]       .text : 0xffff000008080000 - 0xffff000008aa0000   ( 10368 KB)
[    0.000000]     .rodata : 0xffff000008aa0000 - 0xffff000008ed0000   (  4288 KB)
[    0.000000]       .init : 0xffff000008ed0000 - 0xffff000008f90000   (   768 KB)
[    0.000000]       .data : 0xffff000008f90000 - 0xffff00000903ba00   (   687 KB)
[    0.000000]        .bss : 0xffff00000903ba00 - 0xffff0000090a0c10   (   405 KB)
[    0.000000]     fixed   : 0xffff7dfffe7f9000 - 0xffff7dfffec00000   (  4124 KB)
[    0.000000]     PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffff7e0000000000 - 0xffff800000000000   (  2048 GB maximum)
[    0.000000]               0xffff7e0000200000 - 0xffff7e001c000000   (   446 MB actual)
[    0.000000]     memory  : 0xffff800008000000 - 0xffff800700000000   ( 28544 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8.
[    0.000000]  Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125s
[    0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns
[    0.000111] Console: colour dummy device 80x25
[    0.000154] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333)
[    0.000163] pid_max: default: 32768 minimum: 301
[    0.000215] Security Framework initialized
[    0.001810] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.002628] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.002668] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.002696] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.015931] ASID allocator initialised with 32768 entries
[    0.023924] Hierarchical SRCU implementation.
[    0.032724] Detected Renesas R-Car Gen3 r8a7795 ES2.0
[    0.033503] EFI services will not be available.
[    0.039953] smp: Bringing up secondary CPUs ...
[    0.068141] Detected PIPT I-cache on CPU1
[    0.068177] CPU1: Booted secondary processor [411fd073]
[    0.096148] Detected PIPT I-cache on CPU2
[    0.096168] CPU2: Booted secondary processor [411fd073]
[    0.124178] Detected PIPT I-cache on CPU3
[    0.124195] CPU3: Booted secondary processor [411fd073]
[    0.152225] CPU features: enabling workaround for ARM erratum 845719
[    0.152234] Detected VIPT I-cache on CPU4
[    0.152272] CPU4: Booted secondary processor [410fd034]
[    0.180245] Detected VIPT I-cache on CPU5
[    0.180268] CPU5: Booted secondary processor [410fd034]
[    0.208278] Detected VIPT I-cache on CPU6
[    0.208301] CPU6: Booted secondary processor [410fd034]
[    0.236314] Detected VIPT I-cache on CPU7
[    0.236336] CPU7: Booted secondary processor [410fd034]
[    0.236409] smp: Brought up 1 node, 8 CPUs
[    0.236430] SMP: Total of 8 processors activated.
[    0.236436] CPU features: detected feature: 32-bit EL0 Support
[    0.236439] CPU features: detected feature: Kernel page table isolation (KPTI)
[    0.242651] CPU: All CPU(s) started at EL1
[    0.242673] alternatives: patching kernel code
[    0.243395] devtmpfs: initialized
[    0.249718] random: get_random_u32 called from bucket_table_alloc+0x108/0x260 with crng_init=0
[    0.250117] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.250173] futex hash table entries: 2048 (order: 6, 262144 bytes)
[    0.258221] pinctrl core: initialized pinctrl subsystem
[    0.259327] DMI not present or invalid.
[    0.259525] NET: Registered protocol family 16
[    0.260666] cpuidle: using governor menu
[    0.260793] vdso: 2 pages (1 code @ ffff000008aa6000, 1 data @ ffff000008f95000)
[    0.260805] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.261441] DMA: preallocated 256 KiB pool for atomic allocations
[    0.261510] Serial: AMBA PL011 UART driver
[    0.264889] sh-pfc e6060000.pin-controller: r8a77951_pfc support registered
[    0.288589] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.289602] ACPI: Interpreter disabled.
[    0.291833] rcar-avs: use avs value: 0
[    0.291953] rcar-avs: /cpus/cpu@0 is running with: /opp_table0
[    0.291964] rcar-avs: /cpus/cpu@1 is running with: /opp_table0
[    0.291972] rcar-avs: /cpus/cpu@2 is running with: /opp_table0
[    0.291981] rcar-avs: /cpus/cpu@3 is running with: /opp_table0
[    0.292004] rcar-avs: /soc/gsx@fd000000 is running with: /gsx_opp_table0
[    0.293703] ipmmu-vmsa e67b0000.mmu: IPMMU context 0 is reserved
[    0.294239] vgaarb: loaded
[    0.294402] SCSI subsystem initialized
[    0.294665] usbcore: registered new interface driver usbfs
[    0.294689] usbcore: registered new interface driver hub
[    0.294750] usbcore: registered new device driver usb
[    0.295583] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 400000 Hz
[    0.295881] media: Linux media interface: v0.10
[    0.295903] Linux video capture interface: v2.00
[    0.295963] pps_core: LinuxPPS API ver. 1 registered
[    0.295967] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.295976] PTP clock support registered
[    0.296279] EDAC MC: Ver: 3.0.0
[    0.296447] dmi: Firmware registration failed.
[    0.296967] Advanced Linux Sound Architecture Driver Initialized.
[    0.297441] clocksource: Switched to clocksource arch_sys_counter
[    0.297737] VFS: Disk quotas dquot_6.6.0
[    0.297776] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.297870] pnp: PnP ACPI: disabled
[    0.301524] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[    0.301622] NET: Registered protocol family 2
[    0.302056] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.302262] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.302553] TCP: Hash tables configured (established 32768 bind 32768)
[    0.302670] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.302735] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.302883] NET: Registered protocol family 1
[    0.303101] RPC: Registered named UNIX socket transport module.
[    0.303105] RPC: Registered udp transport module.
[    0.303108] RPC: Registered tcp transport module.
[    0.303112] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.304262] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    0.304791] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available
[    0.305203] kvm [1]: HYP mode not available
[    0.306875] audit: initializing netlink subsys (disabled)
[    0.306966] audit: type=2000 audit(0.303:1): state=initialized audit_enabled=0 res=1
[    0.307218] workingset: timestamp_bits=44 max_order=20 bucket_order=0
[    0.310575] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.310965] NFS: Registering the id_resolver key type
[    0.310983] Key type id_resolver registered
[    0.310987] Key type id_legacy registered
[    0.310996] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.311103] 9p: Installing v9fs 9p2000 file system support
[    0.312508] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[    0.312516] io scheduler noop registered
[    0.312521] io scheduler deadline registered
[    0.312603] io scheduler cfq registered (default)
[    0.312608] io scheduler mq-deadline registered
[    0.312612] io scheduler kyber registered
[    0.316210] gpio_rcar e6050000.gpio: driving 16 GPIOs
[    0.316436] gpio_rcar e6051000.gpio: driving 29 GPIOs
[    0.316559] GPIO line 455 (BL PWM 100%) hogged as output/high
[    0.316658] gpio_rcar e6052000.gpio: driving 15 GPIOs
[    0.316863] gpio_rcar e6053000.gpio: driving 16 GPIOs
[    0.316975] GPIO line 432 (MOST RST) hogged as output/high
[    0.317070] gpio_rcar e6054000.gpio: driving 18 GPIOs
[    0.317299] gpio_rcar e6055000.gpio: driving 26 GPIOs
[    0.317418] GPIO line 381 (Onboard MCh Audio) hogged as output/high
[    0.317540] gpio_rcar e6055400.gpio: driving 32 GPIOs
[    0.317737] gpio_rcar e6055800.gpio: driving 4 GPIOs
[    0.318721] rcar-pcie fe000000.pcie: no pcie3v3 regulator found
[    0.318728] rcar-pcie fe000000.pcie: no pcie1v8 regulator found
[    0.318734] OF: PCI: host bridge /soc/pcie@fe000000 ranges:
[    0.318751] OF: PCI:    IO 0xfe100000..0xfe1fffff -> 0x00000000
[    0.318764] OF: PCI:   MEM 0xfe200000..0xfe3fffff -> 0xfe200000
[    0.318772] OF: PCI:   MEM 0x30000000..0x37ffffff -> 0x30000000
[    0.318777] OF: PCI:   MEM 0x38000000..0x3fffffff -> 0x38000000
[    0.385292] rcar-pcie fe000000.pcie: PCIe link down
[    0.386873] EINJ: ACPI disabled.
[    0.402412] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.403687] SuperH (H)SCI(F) driver initialized
[    0.404206] e6540000.serial: ttySC1 at MMIO 0xe6540000 (irq = 35, base_baud = 0) is a hscif
[    0.404800] e6550000.serial: ttySC3 at MMIO 0xe6550000 (irq = 36, base_baud = 0) is a hscif
[    0.405307] e6e68000.serial: ttySC2 at MMIO 0xe6e68000 (irq = 122, base_baud = 0) is a scif
[    0.405786] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 123, base_baud = 0) is a scif
[    1.519923] console [ttySC0] enabled
[    1.525354] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.531975] [drm] No driver support for vblank timestamp query.
[    1.538510] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY)
[    1.548371] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver
[    1.562119] loop: module loaded
[    1.568792] libphy: Fixed MDIO Bus: probed
[    1.573065] tun: Universal TUN/TAP device driver, 1.6
[    1.578257] CAN device driver interface
[    1.582808] rcar_can e6c30000.can: device registered (IRQ120)
[    1.588960] rcar_can e6c38000.can: device registered (IRQ121)
[    1.595206] usbcore: registered new interface driver peak_usb
[    1.601370] thunder-xcv, ver 1.0
[    1.604654] thunder-BGX, ver 1.0
[    1.607906] thunder-nic, ver 1.0
[    1.611520] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.617352] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.623294] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[    1.630258] igb: Copyright (c) 2007-2014 Intel Corporation.
[    1.635852] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[    1.643682] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    1.649753] sky2: driver version 1.30
[    1.654256] libphy: ravb_mii: probed
[    1.658546] ravb e6800000.ethernet eth0: Base address at 0xe6800000, 2e:09:0a:03:93:11, IRQ 117.
[    1.668147] VFIO - User Level meta-driver version: 0.3
[    1.674314] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.680845] ehci-pci: EHCI PCI platform driver
[    1.685311] ehci-platform: EHCI generic platform driver
[    1.711913] ehci-platform ee080100.usb: EHCI Host Controller
[    1.717588] ehci-platform ee080100.usb: new USB bus registered, assigned bus number 1
[    1.725544] ehci-platform ee080100.usb: irq 165, io mem 0xee080100
[    1.745451] ehci-platform ee080100.usb: USB 2.0 started, EHCI 1.10
[    1.751963] hub 1-0:1.0: USB hub found
[    1.755730] hub 1-0:1.0: 1 port detected
[    1.760011] ehci-platform ee0a0100.usb: EHCI Host Controller
[    1.765678] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 2
[    1.773620] ehci-platform ee0a0100.usb: irq 166, io mem 0xee0a0100
[    1.793452] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10
[    1.799888] hub 2-0:1.0: USB hub found
[    1.803652] hub 2-0:1.0: 1 port detected
[    1.807856] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.814048] ohci-pci: OHCI PCI platform driver
[    1.818537] ohci-platform: OHCI generic platform driver
[    1.824073] ohci-platform ee080000.usb: Generic Platform OHCI controller
[    1.830785] ohci-platform ee080000.usb: new USB bus registered, assigned bus number 3
[    1.838682] ohci-platform ee080000.usb: irq 165, io mem 0xee080000
[    1.931712] hub 3-0:1.0: USB hub found
[    1.935476] hub 3-0:1.0: 1 port detected
[    1.939685] ohci-platform ee0a0000.usb: Generic Platform OHCI controller
[    1.946397] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 4
[    1.954293] ohci-platform ee0a0000.usb: irq 166, io mem 0xee0a0000
[    2.047691] hub 4-0:1.0: USB hub found
[    2.051455] hub 4-0:1.0: 1 port detected
[    2.056013] xhci-hcd ee000000.usb: xHCI Host Controller
[    2.061248] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 5
[    2.084653] xhci-hcd ee000000.usb: hcc params 0x014051ce hci version 0x100 quirks 0x0000000000830010
[    2.093811] xhci-hcd ee000000.usb: irq 164, io mem 0xee000000
[    2.099908] hub 5-0:1.0: USB hub found
[    2.103673] hub 5-0:1.0: 1 port detected
[    2.107734] xhci-hcd ee000000.usb: xHCI Host Controller
[    2.112967] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 6
[    2.120367] xhci-hcd ee000000.usb: Host supports USB 3.0  SuperSpeed
[    2.126757] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.135096] hub 6-0:1.0: USB hub found
[    2.138865] hub 6-0:1.0: 1 port detected
[    2.143215] usbcore: registered new interface driver usb-storage
[    2.150867] renesas_usbhs e6590000.usb: no transceiver found
[    2.156603] renesas_usbhs e6590000.usb: gadget probed
[    2.161779] renesas_usbhs e6590000.usb: probed
[    2.167492] i2c /dev entries driver
[    2.178263] cs2000-cp 2-004f: revision - C1
[    2.182605] pca953x 2-0074: 2-0074 supply vcc not found, using dummy regulator
[    2.199490] GPIO line 346 (HUB pwen) hogged as output/high
[    2.206093] GPIO line 347 (HUB rst) hogged as output/high
[    2.212605] GPIO line 348 (OTG OFFVBUSn) hogged as output/low
[    2.219465] GPIO line 349 (OTG EXTLPn) hogged as output/high
[    2.226237] GPIO line 355 (pcm3168a reset) hogged as output/high
[    2.232525] pca953x 2-0075: 2-0075 supply vcc not found, using dummy regulator
[    2.242056] random: fast init done
[    2.252732] GPIO line 330 (GPS rst) hogged as output/high
[    2.259244] GPIO line 333 (FPDLink shdn) hogged as output/high
[    2.265948] i2c-rcar e6510000.i2c: probed
[    2.276101] pca953x 4-0076: 4-0076 supply vcc not found, using dummy regulator
[    2.286735] GPIO line 308 (Video-B A0) hogged as output/low
[    2.292718] GPIO line 309 (Video-B A1) hogged as output/high
[    2.298784] GPIO line 310 (Video-A A0) hogged as output/low
[    2.304767] GPIO line 311 (Video-A A1) hogged as output/high
[    2.310833] GPIO line 316 (CMOS PWDN) hogged as output/high
[    2.316815] GPIO line 317 (CMOS RST) hogged as output/high
[    2.322708] GPIO line 318 (RaspB_IO1) hogged as output/high
[    2.328691] GPIO line 319 (RaspB_IO0) hogged as output/high
[    2.334672] GPIO line 312 (SAM RST) hogged as output/high
[    2.340477] GPIO line 313 (SAM PWR) hogged as output/low
[    2.346196] GPIO line 322 (LVDS switch) hogged as output/high
[    2.352461] pca953x 4-0077: 4-0077 supply vcc not found, using dummy regulator
[    2.363075] GPIO line 292 (mPCIe WAKE#) hogged as output/low
[    2.369141] GPIO line 293 (mPCIe W_DISABLE) hogged as output/high
[    2.375518] GPIO line 294 (mPCIe CLKREQ#) hogged as input
[    2.381205] GPIO line 295 (mPCIe OVC) hogged as input
[    2.386768] i2c-rcar e66d8000.i2c: probed
[    2.391936] i2c i2c-2: Added multiplexed i2c bus 9
[    2.396870] i2c i2c-2: Added multiplexed i2c bus 10
[    2.401860] i2c i2c-2: Added multiplexed i2c bus 11
[    2.406847] i2c i2c-2: Added multiplexed i2c bus 12
[    2.411962] adv7511 13-003d: 13-003d supply avdd not found, using dummy regulator
[    2.419477] adv7511 13-003d: 13-003d supply dvdd not found, using dummy regulator
[    2.426981] adv7511 13-003d: 13-003d supply pvdd not found, using dummy regulator
[    2.434498] adv7511 13-003d: 13-003d supply bgvdd not found, using dummy regulator
[    2.442086] adv7511 13-003d: 13-003d supply dvdd-3v not found, using dummy regulator
[    2.473448] i2c i2c-2: Added multiplexed i2c bus 13
[    2.478464] i2c i2c-2: Added multiplexed i2c bus 14
[    2.484251] edt_ft5x06 15-0038: touchscreen probe failed
[    2.489601] i2c i2c-2: Added multiplexed i2c bus 15
[    2.494791] i2c i2c-2: Added multiplexed i2c bus 16
[    2.499673] pca954x 2-0071: registered 8 multiplexed busses for I2C switch pca9548
[    2.507647] i2c i2c-4: Added multiplexed i2c bus 17
[    2.512998] i2c i2c-4: Added multiplexed i2c bus 18
[    2.517994] i2c i2c-4: Added multiplexed i2c bus 19
[    2.522985] i2c i2c-4: Added multiplexed i2c bus 20
[    2.528036] i2c i2c-4: Added multiplexed i2c bus 21
[    2.533087] i2c i2c-4: Added multiplexed i2c bus 22
[    2.538066] i2c i2c-4: Added multiplexed i2c bus 23
[    2.543171] pca953x 24-0026: 24-0026 supply vcc not found, using dummy regulator
[    2.550779] pca953x 24-0026: failed reading register
[    2.556051] dummy 24-006c: failed reading
[    2.560152] i2c i2c-4: Added multiplexed i2c bus 24
[    2.565033] pca954x 4-0071: registered 8 multiplexed busses for I2C switch pca9548
[    2.573044] ov5642 22-003c: reg_write: i2c write error, reg: 3103
[    2.579465] ov5647_read: i2c read error, reg: 100
[    2.584171] ov5647 21-0036: Camera not available, check power
[    2.590010] ov5647_read: i2c read error, reg: 300a
[    2.594803] ov5647 21-0036: OV5647 not found!
[    2.701835] usb 6-1: new SuperSpeed USB device number 2 using xhci-hcd
[    2.731310] hub 6-1:1.0: USB hub found
[    2.735369] hub 6-1:1.0: 4 ports detected
[    2.850054] ov106xx 18-0060: deserializer does not present
[    2.855583] ov106xx 18-0060: deserializer does not present for OV495
[    2.861980] ov106xx 18-0060: deserializer does not present for OV10640
[    2.868555] ov106xx 18-0060: deserializer does not present for OV2311
[    2.875036] ov106xx 18-0060: deserializer does not present for OV10635
[    2.881608] ov106xx 18-0060: deserializer does not present for OV490
[    2.885446] usb 5-1: new high-speed USB device number 2 using xhci-hcd
[    2.894526] ov106xx 18-0060: deserializer does not present for AR0132
[    2.901009] ov106xx 18-0060: deserializer does not present for AR0140
[    2.907491] ov106xx 18-0060: deserializer does not present for AR0143
[    2.913971] ov106xx 18-0060: deserializer does not present for AR0147
[    2.930510] ov106xx 18-0060: read fail: chip 0x60 register 0x3000: -6
[    2.936989] ov106xx 18-0060: deserializer does not present
[    2.942513] ov106xx 18-0060: deserializer does not present for AP0101
[    2.948990] ov106xx 18-0060: deserializer does not present for GW4200
[    2.955502] ov106xx 18-0060: deserializer does not present
[    2.961024] ov106xx 18-0060: deserializer does not present
[    2.966547] ov106xx 18-0060: deserializer does not present
[    2.972071] ov106xx 18-0060: deserializer does not present for ISX016
[    2.978547] ov106xx 18-0060: deserializer does not present for ISX019
[    2.984989] ov106xx 18-0060: failed to probe @ 0x60 (i2c-4-mux (chan_id 1))
[    2.991957] ov106xx: probe of 18-0060 failed with error -22
[    2.997684] ov106xx 18-0061: deserializer does not present
[    3.003208] ov106xx 18-0061: deserializer does not present for OV495
[    3.009599] ov106xx 18-0061: deserializer does not present for OV10640
[    3.016164] ov106xx 18-0061: deserializer does not present for OV2311
[    3.022640] ov106xx 18-0061: deserializer does not present for OV10635
[    3.029207] ov106xx 18-0061: deserializer does not present for OV490
[    3.035598] ov106xx 18-0061: deserializer does not present for AR0132
[    3.038926] hub 5-1:1.0: USB hub found
[    3.039239] hub 5-1:1.0: 4 ports detected
[    3.049855] ov106xx 18-0061: deserializer does not present for AR0140
[    3.056340] ov106xx 18-0061: deserializer does not present for AR0143
[    3.062822] ov106xx 18-0061: deserializer does not present for AR0147
[    3.079364] ov106xx 18-0061: read fail: chip 0x61 register 0x3000: -6
[    3.085846] ov106xx 18-0061: deserializer does not present
[    3.091368] ov106xx 18-0061: deserializer does not present for AP0101
[    3.097844] ov106xx 18-0061: deserializer does not present for GW4200
[    3.104360] ov106xx 18-0061: deserializer does not present
[    3.109885] ov106xx 18-0061: deserializer does not present
[    3.115406] ov106xx 18-0061: deserializer does not present
[    3.120928] ov106xx 18-0061: deserializer does not present for ISX016
[    3.127404] ov106xx 18-0061: deserializer does not present for ISX019
[    3.133848] ov106xx 18-0061: failed to probe @ 0x61 (i2c-4-mux (chan_id 1))
[    3.140819] ov106xx: probe of 18-0061 failed with error -22
[    3.146557] ov106xx 18-0062: deserializer does not present
[    3.152081] ov106xx 18-0062: deserializer does not present for OV495
[    3.158472] ov106xx 18-0062: deserializer does not present for OV10640
[    3.165038] ov106xx 18-0062: deserializer does not present for OV2311
[    3.171515] ov106xx 18-0062: deserializer does not present for OV10635
[    3.178083] ov106xx 18-0062: deserializer does not present for OV490
[    3.184473] ov106xx 18-0062: deserializer does not present for AR0132
[    3.190952] ov106xx 18-0062: deserializer does not present for AR0140
[    3.197431] ov106xx 18-0062: deserializer does not present for AR0143
[    3.203914] ov106xx 18-0062: deserializer does not present for AR0147
[    3.220450] ov106xx 18-0062: read fail: chip 0x62 register 0x3000: -6
[    3.226932] ov106xx 18-0062: deserializer does not present
[    3.232453] ov106xx 18-0062: deserializer does not present for AP0101
[    3.238929] ov106xx 18-0062: deserializer does not present for GW4200
[    3.245448] ov106xx 18-0062: deserializer does not present
[    3.250969] ov106xx 18-0062: deserializer does not present
[    3.256490] ov106xx 18-0062: deserializer does not present
[    3.262013] ov106xx 18-0062: deserializer does not present for ISX016
[    3.268487] ov106xx 18-0062: deserializer does not present for ISX019
[    3.274929] ov106xx 18-0062: failed to probe @ 0x62 (i2c-4-mux (chan_id 1))
[    3.281894] ov106xx: probe of 18-0062 failed with error -22
[    3.287616] ov106xx 18-0063: deserializer does not present
[    3.293139] ov106xx 18-0063: deserializer does not present for OV495
[    3.299531] ov106xx 18-0063: deserializer does not present for OV10640
[    3.306096] ov106xx 18-0063: deserializer does not present for OV2311
[    3.312572] ov106xx 18-0063: deserializer does not present for OV10635
[    3.319140] ov106xx 18-0063: deserializer does not present for OV490
[    3.325531] ov106xx 18-0063: deserializer does not present for AR0132
[    3.332009] ov106xx 18-0063: deserializer does not present for AR0140
[    3.338487] ov106xx 18-0063: deserializer does not present for AR0143
[    3.344965] ov106xx 18-0063: deserializer does not present for AR0147
[    3.361500] ov106xx 18-0063: read fail: chip 0x63 register 0x3000: -6
[    3.367978] ov106xx 18-0063: deserializer does not present
[    3.373501] ov106xx 18-0063: deserializer does not present for AP0101
[    3.379976] ov106xx 18-0063: deserializer does not present for GW4200
[    3.386488] ov106xx 18-0063: deserializer does not present
[    3.392010] ov106xx 18-0063: deserializer does not present
[    3.397531] ov106xx 18-0063: deserializer does not present
[    3.403053] ov106xx 18-0063: deserializer does not present for ISX016
[    3.409527] ov106xx 18-0063: deserializer does not present for ISX019
[    3.415968] ov106xx 18-0063: failed to probe @ 0x63 (i2c-4-mux (chan_id 1))
[    3.422934] ov106xx: probe of 18-0063 failed with error -22
[    3.429365] rcar_csi2 fea80000.csi2: Data lanes 2, link freq 280
[    3.435561] rcar_csi2 feaa0000.csi2: Data lanes 4, link freq 300
[    3.450383] rcar_gen3_thermal e6198000.thermal: is using pseudo fixed FUSE values
[    3.462087] rcar_gen3_thermal e6198000.thermal: TSC0: Loaded 1 trip points
[    3.473303] rcar_gen3_thermal e6198000.thermal: TSC1: Loaded 1 trip points
[    3.483644] rcar_gen3_thermal e6198000.thermal: TSC2: Loaded 3 trip points
[    3.492402] sdhci: Secure Digital Host Controller Interface driver
[    3.498591] sdhci: Copyright(c) Pierre Ossman
[    3.503681] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO
[    3.569551] renesas_sdhi_internal_dmac ee140000.sd: mmc0 base at 0xee140000 max clock rate 200 MHz
[    3.579150] Synopsys Designware Multimedia Card Interface Driver
[    3.585698] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.592554] ledtrig-cpu: registered to indicate activity on CPUs
[    3.599253] usbcore: registered new interface driver usbhid
[    3.604827] usbhid: USB HID core driver
[    3.608673] mostcore: init()
[    3.611626] aim_cdev: init()
[    3.614535] mostcore: registered new application interfacing module cdev
[    3.621247] mostcore: registered new application interfacing module networking
[    3.628467] aim_sound: init()
[    3.631442] mostcore: registered new application interfacing module sound
[    3.638249] mostcore: registered new application interfacing module v4l
[    3.645449] optee: probing for conduit method from DT.
[    3.650785] optee driver R-Car Rev.1.0.10
[    3.654918] optee: initialized driver
[    3.670579] rcar_sound ec500000.sound: probed
[    3.675273] NET: Registered protocol family 17
[    3.679733] can: controller area network core (rev 20170425 abi 9)
[    3.685989] NET: Registered protocol family 29
[    3.690478] can: raw protocol (rev 20170425)
[    3.694765] can: broadcast manager protocol (rev 20170425 t)
[    3.700486] 9pnet: Installing 9P2000 support
[    3.704817] Key type dns_resolver registered
[    3.709533] registered taskstats version 1
[    3.718269] thermal emergency: set temperature to 110 celsius
[    3.724221] thermal emergency: shutdown target cpus 1-7
[    3.729465] thermal emergency: freq scaled target cpus 0
[    3.735071] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs
[    3.748581] mmc0: new HS400 MMC card at address 0001
[    3.753916] mmcblk0: mmc0:0001 8GSD4R 7.28 GiB
[    3.758656] mmcblk0boot0: mmc0:0001 8GSD4R partition 1 31.9 MiB
[    3.764662] mmcblk0boot1: mmc0:0001 8GSD4R partition 2 31.9 MiB
[    3.770780] mmcblk0rpmb: mmc0:0001 8GSD4R partition 3 512 KiB, chardev (240:0)
[    3.780816]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18
[    3.957458] OF: PCI: host bridge /soc/pcie@ee800000 ranges:
[    3.963055] OF: PCI:    IO 0xee900000..0xee9fffff -> 0x00000000
[    3.968981] OF: PCI:   MEM 0xeea00000..0xeebfffff -> 0xeea00000
[    3.974902] OF: PCI:   MEM 0xc0000000..0xc7ffffff -> 0xc0000000
[    3.980821] OF: PCI:   MEM 0xc8000000..0xcfffffff -> 0xc8000000
[    4.053068] rcar-pcie ee800000.pcie: PCIe link down
[    4.060939] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    4.067566] [drm] No driver support for vblank timestamp query.
[    4.076013] bd9571mwv 7-0030: Device: BD9571MWV rev. 1
[    4.085842] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO
[    4.153853] renesas_sdhi_internal_dmac ee100000.sd: mmc1 base at 0xee100000 max clock rate 200 MHz
[    4.225523] renesas_sdhi_internal_dmac ee160000.sd: mmc2 base at 0xee160000 max clock rate 50 MHz
[    4.247748] asoc-audio-graph-card sound@0: pcm3168a <-> rsnd-dai.0 mapping ok
[    4.254904] asoc-audio-graph-card sound@0: ASoC: no DMI vendor name!
[    4.262841] asoc-audio-graph-card sound@1: ak4613-hifi <-> rsnd-dai.1 mapping ok
[    4.270264] asoc-audio-graph-card sound@1: ASoC: no DMI vendor name!
[    4.279263] asoc-audio-graph-card sound@2: si468x-pcm <-> rsnd-dai.2 mapping ok
[    4.286581] asoc-audio-graph-card sound@2: ASoC: no DMI vendor name!
[    4.297290] asoc-audio-graph-card sound@3: wl18xx-pcm <-> rsnd-dai.3 mapping ok
[    4.304618] asoc-audio-graph-card sound@3: ASoC: no DMI vendor name!
[    4.311337] renesas_sdhi_internal_dmac ee160000.sd: card claims to support voltages below defined range
[    4.321628] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    4.328244] [drm] No driver support for vblank timestamp query.
[    4.348848] mmc2: new high speed SDIO card at address 0001
[    4.397554] Console: switching to colour frame buffer device 160x50
[    4.427680] rcar-du feb00000.display: fb0:  frame buffer device
[    4.434023] [drm] Initialized rcar-du 1.0.0 20130110 for feb00000.display on minor 0
[    4.441770] [drm] Device feb00000.display probed
[    4.447454] input: keyboard as /devices/platform/keyboard/input/input1
[    4.454260] hctosys: unable to open rtc device (rtc0)
[    4.532595] Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PH)
[    7.221477] ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    7.253449] IP-Config: Guessing netmask 255.255.255.0
[    7.258500] IP-Config: Complete:
[    7.261728]      device=eth0, hwaddr=2e:09:0a:03:93:11, ipaddr=192.168.0.2, mask=255.255.255.0, gw=255.255.255.255
[    7.272072]      host=192.168.0.2, domain=, nis-domain=(none)
[    7.277816]      bootserver=255.255.255.255, rootserver=192.168.0.1, rootpath=
[    7.285409] SDHI3 VccQ: disabling
[    7.288732] PCM3168A Vcc Vdd: disabling
[    7.292568] SDHI0 Vcc: disabling
[    7.295797] wlan-en-regulator: disabling
[    7.299724] SDHI3 Vcc: disabling
[    7.302953] amp-en-regulator: disabling
[    7.306790] SDHI0 VccQ: disabling
[    7.310106] ALSA device list:
[    7.313066]   #0: pcm3168a
[    7.315771]   #1: ak4613
[    7.318301]   #2: radio
[    7.320740]   #3: wl18xx
[    7.323554] md: Skipping autodetection of RAID arrays. (raid=autodetect will force)
[    9.376015] VFS: Mounted root (nfs filesystem) on device 0:15.
[    9.382074] devtmpfs: mounted
[    9.385432] Freeing unused kernel memory: 768K
[    9.462124] systemd[1]: System time before build time, advancing clock.
[    9.490299] NET: Registered protocol family 10
[    9.495494] Segment Routing with IPv6
[    9.510157] systemd[1]: systemd 234 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +U)
[    9.531447] systemd[1]: Detected architecture arm64.

Welcome to Poky (Yocto Project Reference Distro) 2.4.3 (rocko)!

[    9.553880] systemd[1]: Set hostname to <h3ulcb>.
[    9.758288] random: systemd: uninitialized urandom read (16 bytes read)
[    9.765028] systemd[1]: Reached target Swap.
[  OK  ] Reached target Swap.
[    9.781756] random: systemd: uninitialized urandom read (16 bytes read)
[    9.788638] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[  OK  ] Started Dispatch Password Requests to Console Directory Watch.
[    9.813532] random: systemd: uninitialized urandom read (16 bytes read)
[    9.820188] systemd[1]: Reached target Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[    9.841731] systemd[1]: Listening on Journal Socket.
[  OK  ] Listening on Journal Socket.
[    9.861605] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.
[    9.885604] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Started Forward Password Requests to Wall Directory Watch.
[    9.909561] systemd[1]: Listening on Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket (/dev/log).
[  OK  ] Listening on Journal Audit Socket.
[  OK  ] Created slice User and Session Slice.
[  OK  ] Reached target Paths.
[  OK  ] Listening on Syslog Socket.
[  OK  ] Listening on udev Control Socket.
[  OK  ] Listening on Network Service Netlink Socket.
[  OK  ] Listening on udev Kernel Socket.
[  OK  ] Created slice System Slice.
         Starting Journal Service...
         Mounting Kernel Debug File System...
[  OK  ] Reached target Slices.
         Starting Load Kernel Modules...
[   10.098638] mmngr: loading out-of-tree module taints kernel.
         Starting Create[   10.106155] rgnmm_drv mmngr: assigned reserved memory node linux,multimedia@70000000
 list of required stce nodes for the current kernel...
         Mounting Huge Pages File System...
         Mounting Temporary Directory (/tmp)...
         Mounting POSIX Message Queue File System...
[  OK  ] Created slice system-getty.slice.
         Starting Remount Root and Kernel File Systems...
[  OK  ] Created slice system-serial\x2dgetty.slice.
[  OK  ] Mounted Kernel Debug File System.
[   10.243855] PVR_K:  1983: HTBInit: HTBufferSizeInKB = 64
[  OK  ] Mounted POSIX Message Queue File Syste[   10.255075] PVR_K:  1983: RGX Device initialised with BVNC 4.46.6.62
m.
[   10.262807] pvrsrvkm fd000000.gsx: opp[1/4]: (200000000 Hz, 830000 uV)
[   10.269573] pvrsrvkm fd000000.gsx: opp[2/4]: (300000000 Hz, 830000 uV)
[   10.276118] pvrsrvkm fd000000.gsx: opp[3/4]: (400000000 Hz, 830000 uV)
[   10.282653] pvrsrvkm fd000000.gsx: opp[4/4]: (600000000 Hz, 830000 uV)
[   10.289583] [drm] Initialized pvr 1.10.5187610 20170530 for fd000000.gsx on minor 1
[  OK  ] Mounted Huge Pages File System.
[   10.302804] imr fe860000.imr0: IMR device (pdev: -1) registered as /dev/video0
[   10.310362] imr fe870000.imr1: IMR device (pdev: -1) registered as /dev/video1
[   10.317924] imr fe880000.imr2: IMR device (pdev: -1) registered as /dev/video2
[   10.325430] imr fe890000.imr3: IMR device (pdev: -1) registered as /dev/video3
[  OK  ] Mounted Temporary Directory (/tmp).
[  OK  ] Started Journal Service.
[  OK  ] Started Load Kernel Modules.
[  OK  ] Started Create list of required stavice nodes for the current kernel.
[  OK  ] Started Remount Root and Kernel File Systems.
         Starting udev Coldplug all Devices...
         Starting Create Static Device Nodes in /dev...
         Starting Apply Kernel Variables...
         Mounting Kernel Configuration File System...
         Starting Flush Journal to Persistent Storage...
[  OK  ] Mounted Kernel Configuration File System.
[  OK  ] Started Create Static Device Nodes in /dev.
[  OK  ] Started Apply Kernel Variables.
         Starting udev Kernel Device Manager...
[  OK  ] Reached target Local File Systems (Pre).
         Mounting /var/volatile...
[  OK  ] Mounted /var/volatile.
[  OK  ] Started udev Kernel Device Manager.
[   10.649012] systemd-journald[1981]: Received request to flush runtime journal from PID 1
         Starting Load/Save Random Seed...
[   10.675814] random: crng init done
[   10.679219] random: 7 urandom warning(s) missed due to ratelimiting
[  OK  ] Reached target Local File Systems.
[  OK  ] Started Flush Journal to Persistent Storage.
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started udev Coldplug all Devices.
         Starting Create Volatile Files and Directories...
[  OK  ] Started Create Volatile Files and Directories.
         Starting Update UTMP about System Boot/Shutdown...
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[   10.887853] lsm9ds0 16-001d: Accelerometer and magnetometer found.
[  OK  ] Reached target System Initialization.
[   10.900127] lsm9ds0 16-006b: Gyroscope found.
[  OK  ] Started dnf-automatic-download timer.
         Starting Network Service...
[  OK  ] Started dnf makecache timer.
[  OK  ] Listening on D-Bus System Message Bus Socket.
         Starting sshd.socket.
[  OK  ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[  OK  ] Listening on RPCbind Server Activation Socket.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Started dnf-automatic-notifyonly timer.
[  OK  ] Started dnf-automatic-install timer.
[  OK  ] Reached target Timers.
[  OK  ] Listening on sshd.socket.
[  OK  ] Found device /dev/ttySC0.
[   11.314281] wl18xx_driver wl18xx.5.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error 2
[   11.325003] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -2
[   11.333808] wlcore: WARNING falling back to default config
[  OK  ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
[  OK  ] Reached target Sound Card.
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Basic System.
         Starting PowerVR consumer services...
         Starting Spacenavd startup...
[  OK  ] Started System Logging Service.
[  OK  ] Started optee services.
[  OK  ] Started Kernel Logging Service.
         Starting Telephony service...
[  OK  ] Reached target Containers.
         Starting pvrinit.service...
         Starting Login [   11.634642] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
Service...
[   11.646363] wlcore: WARNING Detected unconfigured mac address in nvs, derive from fuse instead.
[   11.646363]
[   11.656558] wlcore: WARNING This default nvs file can be removed from the file system
[   11.656558]
[   11.679365] wlcore: loaded
[  OK  ] Started D-Bus System Message Bus.
[  OK  ] Started Telephony service.
         Starting Avahi mDNS/DNS-SD Stack...
         Starting Save/Restore Sound Card State...
[   11.771686] Bluetooth: Core ver 2.22
[   11.775433] NET: Registered protocol family 31
[   11.779910] Bluetooth: HCI device and connection manager initialized
[   11.786334] Bluetooth: HCI socket layer initialized
[   11.791235] Bluetooth: L2CAP socket layer initialized
[   11.796334] Bluetooth: SCO socket layer initialized
[  OK  ] Started Network Service.
[  OK  ] Started PowerVR consumer services.
[  OK  ] Started Spacenavd startup.
[  OK  ] Started pvrinit.service.
[  OK  ] Started Save/Restore Sound Card State.
[  OK  ] Started Avahi mDNS/DNS-SD Stack.
[  OK  ] Started Login Service.
         Starting Load/Save RF Kill Switch Status...
         Starting rc.mm.service...
[  OK  ] Reached target Network.
         Starting Network Name Resolution...
         Starting Permit User Sessions...
         Starting Target Communication Framework agent...
[  OK  ] Started Load/Save RF Kill Switch Status.
[  OK  ] Started rc.mm.service.
[  OK  ] Started Permit User Sessions.
[  OK  ] Started Target Communication Framework agent.
[  OK  ] Started Getty on tty1.
[  OK  ] Started Serial Getty on ttySC0.
[  OK  ] Reached target Login Prompts.
         Starting uim-sysfs.service...
[   12.146215] (stk) :sysfs entries created
[  OK  ] Started Network Name Resolution.
[  OK  ] Reached target Host and Network Name Lookups.
[   12.359825] (stc):  chnl_id list empty :4
[  OK  ] Started uim-sysfs.service.
         Starting pulseaudio.service...
         Starting Bluetooth service...
[  OK  ] Started Bluetooth service.
[  OK  ] Reached target Bluetooth.
[   12.359836] (stk) : st_kim_start
[   12.462783] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   12.469730] (stk) :ldisc_install = 1
[   12.471385] Bluetooth: BNEP socket layer initialized
         Starting Hostname Service...
[   12.622175] (stc): st_tty_open
[  OK  ] Started Hostname Service.
[   12.622196] (stk) :line discipline installed
[   12.645748] (stk) :ti-connectivity/TIInit_11.8.32.bts
[   12.651763] (stk) :change remote baud rate command in firmware
[  OK  ] Started pulseaudio.service.
[  OK  ] Reached target Multi-User System.
[  OK  ] Started Weston Wayland compositor.
         Starting Update UTMP about System Runlevel Changes...
[  OK  ] Started Update UTMP about System Runlevel Changes.
[   12.656865] (stk) :skipping the wait event of change remote baud
[   13.997385] audit: type=1006 audit(1580798983.527:2): pid=3659 uid=0 old-auid=4294967295 auid=0 tty=(none) old-ses=41

Poky (Yocto Project Reference Distro) 2.4.3 h3ulcb ttySC0

h3ulcb login: root
Last login: Tue Feb  4 06:49:43 UTC 2020 on tty2
root@h3ulcb:~# uname -a
Linux h3ulcb 4.14.75-ltsi-yocto-standard #1 SMP PREEMPT Fri Mar 13 06:23:48 UTC 2020 aarch64 aarch64 aarch64 GNU/Linux
root@h3ulcb:~#
